Flexible Solar Panel Installed On Roof and On Hood

Lensun 90W Solar Panel Mounted On The Hood and 50W Flexible Solar Panel Mounted On The Roof of Toyota Tacoma(2005-2015) 2nd Gen.

William Purcahsed 1Pcs 90W solar panel for the hood and another 50W solar panel for the roof of his Toyota Tacoma 2nd Gen (2005-2015).

SOLAR PANEL INSTALLED ON HOOD

The hood solar panel for Toyota Tacoma 2nd Gen (2005-2015) Available At:

The Hood Solar Panel for Tacoma 2nd Gen

After installing solar panel of the hood, William felt that his truck’s roof was also an excellent place to install solar panel which can add extra energy without wasting the area of it, so William installed another 50W solar panel on the roof of his Tacoma 2rd Gen.

The roof solar panel for Toyota Tacoma 2nd Gen (2005-2015) Available At:

The Roof Solar Panel for Tacoma 2nd Gen


ACCESSORIES FOR INSTALLATION

3M VHB 5952 (Black) 1” wide 15ft.  used 1 roll plus about 10” from 2nd roll.

Dualplex neoprene sponge foam rubber roll 1 sided adhesive 15x60x1/16”. Used 1 roll.

Dualplex neoprene sponge foam rubber roll 1 sided adhesive 15x60x1/8”. Used 1 roll.

All items purchased on Amazon.

INSTALLATION

STEP 1: CLEAN THE SOLAR PANEL

Clean Solar Panel with alcohol before applying 3M tape!!!

STEP 2: LAY OUT THE TAPE

Use 2 rows of 1” wide 3M tape to align with each roof rib. 

Center to center spacing approximately 10 1/8”

Add 1 row of 3M tape atop the foam layers (center of foam), (3 places)

1/16” foam layer plus 1/8” foam layer filled in area between rib tape 3 places. You must leave at least ½” gap between foam and 3M tape to avoid the angle portion of roof ribs.

Note: Some small air bubbles will appear under the foam. These can be punctured with the corner of a razor blade.

STEP 3: FILLED WITH FOAM TAPE

NOTE1: Wash and then Clay bar roof area prior to installing the vinyl underlay.  I used “Mothers Detailer”

NOTE2: Clean with alcohol before applying Foam tape and Roof Solar Panel!!!  3M VHB tape must be free of contaminates for best adhesion. It also requires 72 hours to reach100% strength.

STEP 4: PUT THE PANEL ON THE ROOF

STEP 5: LAY OUT THE CABLE

STEP 6: INSTALLATION FINISHED

This 50W solar panel is designed to fit the Gladiator JT. Its dimensions are 32.7×14”. A larger panel will fit the top area of a 2014 Tacoma Access cab.  Use caution as the cab roof arch increases as it goes wider (front to back). A panel as wide as 28-29” may be possible but 21-22” would be a safer bet.

Vinyl Underlay was made larger than required in case the leading edge of the roof solar panel began to lift away at high speeds.  The intent was to add Eternabond tape if this happened.  80-90MPH speeds and panel is still holding solid.

LENSUN provides hood solar panels for various models of truck, Available At: Hood Solar Panel.


LENSUN provides roof solar panels for various models of truck, Available At: Roof Solar Panel.

 

If there has any questions or advice, please contact us or call us in the following information from Mondays to Fridays. Any wholesale requests just call us or email us, thanks.

Contact information
www.lensunsolar.com
Tel: US +1 720-608-1288
China: +86 15759769602
Whatsapp:  +86 15759769602
Skype: lensunsolar
Email: [email protected][email protected]

Leave a Reply

Solve : *
26 + 14 =