Sharing Michael’s installation of solar panel on his boat, Lensun Solar

We are very glad that Michael shared his installation for #Lensun solar panel on his boat with us.

We are very glad that Michael shared his installation for #Lensun solar panel on his boat with us.

packing-lensun-stronger-100w-18v-12v-charge-flexible-solar-panel-sunpower-solar-cells-grade-a-cells-monocrystal

He was very pleased with how well Lensun 100W flexible solar panel was packed. The outer cardboard was reasonably strong.The inner cardboard liner was pretty robust.

Lensun-100W-12V-monocrystal-sunpower-solar-cells-flexible-solar-panel-ETFE-black-fiberglass-solar-power-system-electric-energy

short-circuit-current-for-100W-lensun-flexible-solar-panel-solar-powerVoltage-for-lensun-100W-flexible-solar-panel-reasonable-for-late-afternoon

He did check the panel with a multimeter before installation, Voltage was 20.4V, short circuit current was 5.17A. It is a reasonable for late afternoon.

Install-100W-lensun-flexible-solar-panel-sunpower-solar-cells-ETFE

He  fixed the cable to one corner using a cable tie, then passed tape though the holes in each corner and stitched the tape to itself with UV resistant thread.

install-Lensun-100W-solar-panel-semi-flexible-solar-panel-sunpower-solar-grade-a-cells-in-awning-of-boat

The wiring lies on top of the awning and is held in place by Velcro next to the cable (but not attached yet).

MC4-Connectors-cables-for-solar-panel-Lensun-100W-solar-panel-sunpower-solar-power-solar-system-for-charge-batteries

The tape passes through webbing stitched to the awning and is pulled to the rear where it is fixed.  The panel cannot lift from the awning as it is held firmly at each corner.  Each webbing strip has a backing pad to provide additional strength.

Lensun-100W-solar-panel-insatallation-for-marine-yacht-boat-sunpower-high efficiency-flexible-solar-cells-solar-power

The wiring is attached to the backstay using velcro

wiring-lensun-100w-solar-panel-monocrystal-on-boat

A waterproof Bulgin 7000 series Bucaneer plug and socket connect to the regulator beside the batteries.  He also have a 20A inline fuse at the battery to protect the wiring.

Bottom-Wiring-lensun-100W-solar-panel-to-solar-controller-regulator-charge-12V-battery

All wiring above and below deck is HO7RN-F 2 core (4mm2) to provide abrasion and UV resistance.

Connections to panel and plug are coated with Contralube 770.

Joint between HO7RN-F wire and tail to panel connectors is soldered, coated with Contralube 770 and sealed in self-amalgamating tape.

N.B.  The tape loops and Velcro cable ties make it easy to remove the panel when strong wind is forecast.  We would normally remove the panel if wind of more than 30kts is forecast.  However, that’s really to protect the awning rather than the panel and this only takes a few minutes.

Lensun-100W-monocrystal-flexible-solar-panel-power-for-12V-charge-batteries-sunpower-solar-cells-ETFE-yacht-boat-motorhome-rvs-caravan-car-bus-camping-van-camper

detail-lensun-100W-solar-panel-ETFE

Panel specs. are based on conditions which will never be achieved in real use. The following table shows more realistic daily output for use on a boat in South of France. Quoted as Ah/day for a 100W panel.

Daily-output-for-use-on-a-boat-in-South-of-France-for-a-100W-panel-lensun
Contact information
www.lensunsolar.com
Tel: US +1 720-608-1288
China: +86 15759769602
Whatsapp: +86 15759769602
Skype: lensunsolar
Email: [email protected], [email protected]

Leave a Reply

Solve : *
8 + 13 =